How to Test Coffee Moisture Content with a Moisture Analyzer

By Lim Xu, Export Manager

How to test coffee moisture content with a halogen moisture analyzer for green, roasted and instant coffee, and how to check it against the oven reference.

Coffee moisture content changes how a lot is traded, stored and roasted. A halogen moisture analyzer can give a fast reading in the lab, but the result only holds if you treat it as a rapid method and check it against the oven reference for that stage of coffee.

Why moisture matters at each coffee stage

Green coffee that is too wet is more likely to spoil in storage. Coffee that is too dry loses mass and can break in handling. Traders and roasters therefore treat moisture as a condition of the lot, not as an afterthought.

Roasted coffee and instant coffee have their own targets, because water left after roasting or drying affects shelf life and clumping. The figure you write down should always name the stage, the method and whether the sample was whole or ground.

If you mix stages in one log, a later reader cannot tell whether a shift came from the coffee or from the test.

Reference methods for green, roasted and instant coffee

The usual reference is an oven method, not the analyzer itself. ISO 6673 covers loss in mass of green coffee. ISO 11294 covers moisture in roasted ground coffee by loss in mass. ISO 3726 covers loss in mass of instant coffee under reduced pressure.

Those documents describe official oven or vacuum-oven procedures. The KHT-HMA-01 halogen moisture analyzer lists GB/T 462 and ISO 287, which are paper moisture methods. It does not claim to comply with ISO 6673, ISO 11294 or ISO 3726.

Use the ISO method named for the stage as the reference, and use the analyzer as a faster lab method that you have checked against that reference. If you need a target moisture range for a contract, please confirm it with us against the trading rule or published guide you follow. We will not invent a range here.

Measuring coffee with a halogen moisture analyzer

A halogen analyzer dries a weighed sample with a halogen lamp and reports moisture from the loss in mass. The same idea sits behind oven methods, which is why labs often compare the two. For a broader comparison of the two approaches, see drying oven vs halogen moisture analyzer.

KHT-HMA-01 takes a maximum sample of 110 g, weighs to 0.001 g, and dries between 40 and 160 °C in 1 °C steps. Moisture is reported from 0.00 to 100.00 % with a resolution of 0.01 %. Those figures come from the verified model file. They are instrument limits, not a coffee method.

Not sure how your coffee will behave on a halogen analyzer? Tell us what you need to test. We test a similar material sample and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.

Whole bean vs ground sample

Whole beans dry slowly and unevenly, because the centre lags the surface. Most oven references for roasted coffee start from a ground sample. If you run beans whole on the analyzer, say so in the record, and do not treat that result as equal to a ground-sample reference.

Grind just before the test, use a consistent mill setting, and avoid heating the sample in the mill. Spread the grounds in a thin, even layer in the pan so the lamp does not scorch one side.

Drying temperature and end point

Pick one temperature and one end-point rule and keep them for that coffee type. A temperature that is too high can drive off more than water or scorch the sample. A temperature that is too low leaves the reading unfinished.

Published coffee methods use different oven temperatures for green, roasted and instant coffee. Do not copy those temperatures onto the analyzer unless you have compared results on your own lots. For how to think about analyzer temperature in general, see halogen moisture analyzer temperature settings. If you want a starting point for a named coffee type, please confirm with us.

Stop the test by a stable-mass rule, not by a fixed clock time alone. Record the temperature, the end-point rule, the sample mass and whether the coffee was green, roasted or instant.

Moisture analyzer vs coffee moisture meter

A coffee moisture meter, often a capacitance or resistance meter used on whole beans, is built for quick checks in a warehouse or at intake. It usually needs a calibration for the coffee type, and it does not dry the sample.

A halogen moisture analyzer dries a prepared sample and computes loss in mass. It is slower than a meter, but the principle is closer to the oven reference. Use a meter for intake screening if you already have one, and use the analyzer plus the oven method when you need a lab result you can defend.

Do not average a meter reading and an analyzer reading as if they were the same test.

Matching the analyzer to the reference method

Run the analyzer and the named ISO method on the same lot, ground the same way, until you know the offset for that coffee and that temperature. Keep the comparison when the origin, roast or grade changes.

Write the reference method name on the certificate or lab sheet, even when the daily result comes from the analyzer. If the two methods disagree by more than your agreed tolerance, do not ship on the analyzer figure alone.

KHT Instruments has made packaging and lab test equipment since 2013, with a 1,000 m² factory in Jinan, China. Datasheets for KHT-HMA-01 are available on request from KHT.

Frequently asked questions

Can a halogen analyzer replace ISO 6673 for green coffee?

No. ISO 6673 remains the reference for green coffee loss in mass. The analyzer is a rapid lab method that you should check against that reference on your own lots.

Should parchment coffee be tested like green coffee?

Parchment is not the same as hulled green coffee. If your contract names a method for parchment, follow that method. Please confirm with us before you reuse a green-coffee program.

Does a test video replace a quotation?

No. The video shows how a similar sample behaves on the instrument. A quotation still needs the model, the options and the shipping details you ask us to include.

Get a test video for your samples

Tell us what you need to test, such as the material, the size and the test method. We test a similar material sample on the instrument you are looking at and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.

Questions about a model or a test? Email Amy Zhao, Export Manager, at [email protected].

Related articles

Get Your Free Quote

Looking for the right analyzer? Talk to our experts and find the best solution for your application.

View our privacy policy.

© 2026 Halogen Moisture Analyzer | All rights reserved.