How to Clean a Moisture Analyzer Pan, Chamber and Sensor

By Lim Xu, Export Manager

How to clean a moisture analyzer sample pan, drying chamber and temperature sensor safely after a test, and which checks to run before the next sample.

A moisture analyzer weighs a sample, dries it and weighs it again, so anything left behind from the last test becomes part of the next result. This page explains how to clean the sample pan, the drying chamber and the temperature sensor area after a test, what to check once cleaning is done, and when to ask us or follow the instrument manual instead of guessing.

The examples below refer to the KHT-HMA-01 halogen moisture analyzer, which uses a Ø90 mm sample pan, halogen lamp heating from 40 to 160 °C, a weighing resolution of 0.001 g and a maximum sample of 110 g. The cleaning routine itself applies to halogen moisture analyzers in general: keep residue out of the weighing and drying path, and let the instrument cool and dry fully before the next run.

Why residue changes moisture results

Residue changes a moisture result in two ways. First, material left on the pan or in the chamber adds weight that is not part of the new sample. On an instrument that resolves 0.001 g, even a thin film of powder, oil or dried sample can shift the starting weight and the end weight.

Second, residue does not behave like the fresh sample. Old material can absorb moisture from the air between tests and release it during drying, or it can scorch and lose weight a second time. Either way, the loss the instrument records no longer comes only from the sample you placed on the pan, and repeat runs of the same material stop agreeing with each other.

Spilled sample is the most common source. Powder that misses the pan, droplets that splash during drying and fibres that stick to the chamber wall all stay in the drying space until someone removes them. Cleaning is therefore part of measurement, not housekeeping after it.

What to clean and how often

Clean the parts that touch the sample or sit in the drying path. How often each part needs a full clean depends on the samples you run and on the instrument manual for your model. Sticky, sugary, oily or strongly coloured samples leave more behind than dry powders, so check the pan and chamber after every test with those materials and follow the manual for the cleaning interval for your instrument. If you do not have the manual, ask us before you settle on an interval of your own.

Sample pan and pan holder

The sample pan and its holder carry the sample through the whole test, so they collect the most residue. Remove loose material from the pan after each test, and wash or wipe the pan when a film, stain or baked-on layer remains after brushing. A pan that is not fully dry, or that still carries a film, goes into the next test with extra weight already on it.

Reusable pans should sit flat and undamaged. A bent or scratched pan changes how a thin sample layer spreads, so set damaged pans aside rather than returning them to the drawer with the others.

Drying chamber, draft shield and glass

Powder and vapour from drying settle on the chamber wall, the draft shield and any glass in the drying space. Wipe these surfaces once they have cooled, working from the top of the chamber down so loosened powder does not fall back onto a surface you have already cleaned.

Do not take the draft shield or chamber apart to reach a hidden surface unless the instrument manual for your model shows how that part comes off and goes back. If a surface cannot be reached with the parts in place, ask us how it is cleaned on your model instead of prising parts open.

Temperature sensor and reflector area

The temperature sensor and the reflector area around the heating zone control how evenly the sample dries. Dust and spatter on these surfaces can make the heat at the sample differ from the temperature the instrument is working to, so keep them clear of loose residue and check them when you clean the chamber.

Treat this area gently and do not remove the sensor unless the manual shows the procedure. The halogen lamp itself is a separate topic, covered in our guide to the moisture analyzer halogen lamp, and it is not part of the routine in this page.

Questions about a model or a test? Email Amy Zhao, Export Manager, at [email protected].

Safe cleaning steps after a test

Work in this order once a test has finished:

  1. Switch the instrument off and let the pan, chamber and heating area cool fully. Parts that were drying a sample at up to 160 °C stay hot after the run ends.
  2. Open the chamber and take out the sample pan and holder. Tip loose residue into a waste container and brush the pan and holder clean.
  3. Wipe the chamber wall, draft shield and glass with a soft, dry or slightly damp cloth, following the instrument manual for your model. Work gently around the sensor and reflector area and do not press on the sensor.
  4. Deal with baked-on or sticky residue by softening and lifting it as the manual directs. Do not use a cleaning agent unless the manual lists it for that part: an agent that leaves a film of its own adds residue instead of removing it, and an agent that attacks a coating or seal creates a new problem.
  5. Leave every cleaned part fully dry before you close the chamber or run the next test. Moisture left from cleaning is read as moisture in the next sample.
  6. Put the pan and holder back, close the chamber and run the checks in the next section before the next sample goes in.

If a spill reaches a part you cannot clean with the steps above, or a cleaning agent not listed in the manual has already been used inside the chamber, stop and ask us how to proceed on your model rather than repeating the clean with a stronger agent.

Checks after cleaning

Cleaning changes the state of the instrument, so run a short check before the next sample. Confirm the pan sits flat on its holder, the chamber closes as it should, and the empty-pan reading is stable at zero.

Then run the weighing and temperature checks set out in our guide to halogen moisture analyzer calibration. A stable zero with a drifting weighing or temperature check points to a calibration or service question, not a cleaning one, and cleaning the same parts again will not settle it.

Keep a short note of what you cleaned and what the check showed. When a result later looks wrong, that note tells you whether the instrument had just been cleaned, which parts were touched and whether the check afterwards was normal.

Disposable pans and accessories

Disposable sample pans remove one cleaning step: a used pan is thrown away instead of washed, so baked-on residue does not carry into the next test. They do not remove the need to clean the chamber, the holder or the sensor area, because spills and vapour still reach those parts.

Whether disposable pans are supplied with the instrument or ordered separately depends on the model and the order, so ask us what is included before you assume a supply is in the box. The pans and other accessories for this instrument are listed on the halogen moisture analyzer accessories page. Datasheets are available on request from KHT.

Every KHT instrument comes with a 2-year warranty on the complete instrument, counted from the day it leaves our factory. Wear parts and components subject to normal wear are not covered. Labor and shipping costs are not included in the warranty.

Frequently asked questions

Which cleaning agent should I use inside the chamber?

Use only an agent the instrument manual lists for that part. We do not specify a cleaning agent for the chamber or the sensor area in this page, because the right choice depends on the model and its surfaces. If your manual does not name one, ask us before you use anything.

How often should I clean the moisture analyzer?

Check the pan and chamber after every test and clean them whenever residue remains. The interval for a fuller clean of the chamber and sensor area is set by the samples you run and by the instrument manual for your model, so follow the manual and ask us if you do not have it.

Can I remove the draft shield or the temperature sensor to clean behind them?

Do not remove either part unless the instrument manual for your model shows how it comes off and goes back. Clean the surfaces you can reach with the parts in place, and ask us how a surface you cannot reach is cleaned on your model.

Do disposable pans mean I can skip chamber cleaning?

No. A disposable pan replaces the pan you would otherwise wash. Spills, powder and vapour still reach the holder, the chamber wall and the sensor area, and those parts still need the routine above.

See your material tested before you decide

KHT Instruments has made packaging test equipment in Jinan, China, since 2013 and runs a 1,000 m² factory there. We sell direct from our factory, so you work directly with our factory team.

Tell us what you need to test. We test a similar material sample and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too. The test and the video are free of charge.

Questions about a model or a test? Email Amy Zhao, Export Manager, at [email protected]. To ask for a quotation on the instrument, the pans or the accessories covered in this page, Request a Quote through the same address and tell us the model and the samples you run.

Related articles

Get Your Free Quote

Looking for the right analyzer? Talk to our experts and find the best solution for your application.

View our privacy policy.

© 2026 Halogen Moisture Analyzer | All rights reserved.